Torsion Spring Torque, Leg Position and Winding Direction Explained

Torque, leg position, and winding direction define a torsion spring, and torsion spring manufacturers cannot produce a dependable part unless all three appear on the drawing. Torque equals force multiplied by distance, and a spring delivers it at a stated angle between the legs. Wire diameter, coil diameter, and active coils set the torque rate, with wire diameter having the largest effect because it enters the calculation to the fourth power. Leg position fixes where the legs sit in the free state and where they finish under load. Winding direction, right-hand or left-hand, must match the direction of loading so the coil tightens instead of opening. A mismatch in any one of these causes torque errors, early fatigue, or a spring that does not fit the mechanism. At Accurate Springs Pvt Ltd, we check all three before a design goes to production, and the sections below explain how each one works and how they affect one another.

How Torsion Spring Torque Is Calculated

Torque equals the applied force multiplied by its perpendicular distance from the coil axis. A force of 5 N applied 40 mm from the axis produces 200 N·mm. The spring stores this torque in proportion to deflection, and the relationship stays linear throughout the working range.

For round wire, the torque rate per degree of deflection follows this formula:

  • Rate (N·mm per degree) = E × d⁴ ÷ (3667 × D × Na)
  • E: modulus of elasticity of the wire in MPa
  • d: wire diameter in mm
  • D: mean coil diameter in mm
  • Na: number of active coils

The legs contribute to Na. Active coils equal the body coils plus (L1 + L2) ÷ (3π × D), where L1 and L2 are the leg lengths. Long legs soften the spring, so a design with 6 body coils and long straight legs can behave like one with 6.5 active coils or more. The drawing has to state leg length for this reason.

Wire diameter has the strongest influence. Raising it from 1.0 mm to 1.1 mm increases the torque rate by about 46 percent.

The stress in a torsion spring is bending stress, not torsional stress, and the inside of the coil carries the highest value. We apply a curvature correction factor when we check stress at the working angle. Music wire to ASTM A228 and stainless steel grades 302 and 304 are the most common materials, and low-temperature stress relief after coiling stabilizes both dimensions and torque. Commercial torque tolerance is commonly ±10 percent at the stated angle.

Leg Position and Free Angle

Leg position describes the angle between the two legs when the spring carries no load. This is the free angle. The working angle is the position between the legs once the spring is installed and delivering its design torque. Torque should always be specified at a working angle, for example 120 N·mm at 60 degrees between legs.

That link between angle and torque has direct consequences. A spring with a rate of 4 N·mm per degree and a free angle off by 5 degrees delivers 20 N·mm more or less at the same installed angle.

The fractional part of the body coil count sets the free angle. With tangent legs, 6.25 body coils place the legs at 90 degrees to each other. Production coiling adjusts the fractional coils to reach the drawing angle.

Straight tangent legs suit most clamp and latch assemblies, hook ends attach to pins, and double torsion springs join a right-hand and a left-hand coil section at the center.

Winding Direction and Loading Direction

Winding direction describes the hand of the helix, using the same convention as a screw thread. A torsion spring should be loaded in the direction that tightens the coil. Residual stresses from coiling oppose the working stress in that direction, so the wire accepts a higher stress and lasts longer. Loading in the opening direction raises the stress in the coil and can cause yielding or early breakage.

Paired installations show the problem clearly. Garage door systems use one left-hand and one right-hand wound spring because they sit on opposite ends of the shaft. Swap them and one spring works in the unwinding direction.

Winding also changes coil diameter. A spring with 6 body coils deflected through 90 degrees loses about 4 percent of its mean diameter. The arbor must stay clear of the inside diameter at full deflection, and we generally size it to about 90 percent of the minimum inside diameter. A tight arbor adds friction and reduces the torque you measure.

Specify the winding hand together with the loading direction on an end view of the drawing. The words “right-hand wound” alone leave room for interpretation.

How the Three Specifications Interact

The three specifications depend on one another, so a change to one alters the others. Adding half a coil to lower the torque rate rotates the free leg position by 180 degrees, so the legs must be reformed. Increasing wire diameter to raise torque shrinks the arbor clearance under load. Switching from right-hand to left-hand mirrors the leg layout, and the original drawing cannot be reused without redrawing it.

Specification Errors We See on Drawings

  • Torque without an angle: the supplier cannot set the free angle, so the part misses the target in assembly.
  • Leg angle without a measuring direction: clockwise and counterclockwise readings differ, and the legs end up 270 degrees apart instead of 90.
  • Winding hand that contradicts the load direction: the spring opens under load and fails early.
  • No leg length: active coils change, and the torque rate shifts with them.

What We Need to Quote a Torsion Spring

You can reduce quotation time by sending the following with your enquiry:

  • Wire material, wire diameter, and coil diameter
  • Free angle or body coils, leg length, and leg shape
  • Winding hand, loading direction, and arbor diameter
  • Torque at a stated working angle
  • Operating environment, cycle life, and order quantity

At Accurate Springs Pvt Ltd, we compare these inputs against a calculated rate and verify that stress at the working angle stays within the allowable range for the material before we propose a design.

Conclusion

Torque, leg position, and winding direction decide how a torsion spring behaves in service, and each one needs a stated value, angle, or direction on the drawing. A torque figure without an angle, or a winding hand without a load direction, produces parts that measure correctly and still fail in the assembly. When you compare spring manufacturers in India, ask for a drawing review that confirms all three before production begins. We at Accurate Springs Pvt Ltd provide that review for every torsion spring enquiry, and you can send us your drawing or application details to receive a calculated specification.

Frequently Asked Questions

How do you calculate torque in a torsion spring?

Multiply the rate per degree by the deflection in degrees. The rate comes from the wire modulus, wire diameter to the fourth power, coil diameter, and active coils. A spring rated at 4 N·mm per degree and deflected 30 degrees delivers 120 N·mm.

What is the free angle of a torsion spring?

The free angle is the angle between the legs with no load applied. It is set during coiling by the fractional number of body coils. Torque at any installed position depends on how far that position sits from the free angle.

How do you choose between right-hand and left-hand winding?

Choose the hand that tightens the coil in the direction your mechanism loads the spring. Check this against the rotation shown on an end view of your assembly. Paired springs on opposite sides of a shaft normally require opposite hands.

Why does wire diameter change torque so much?

Wire diameter enters the rate formula to the fourth power. A change of 0.1 mm on a 1.0 mm wire shifts the rate by about 46 percent. Coil diameter and coil count affect the rate in direct proportion, so they change it far less.

What tolerance applies to torque and leg position?

Commercial torque tolerance is commonly ±10 percent at the stated angle, and tighter values require closer control of wire properties and coiling. Leg position tolerance is commonly stated in degrees. Both depend on wire size, coil count, and leg length.

Recommended Posts

No comment yet, add your voice below!


Add a Comment

Your email address will not be published. Required fields are marked *